Electronic Dog Collars - $45
Purchased about 6 months ago but used only a few times. Comes with 2 receivers and 1 remote to control 2 dogs at a time. I you do not wish to use the shock function (as this should be used together with training), you may adjust for vibration function only or the sound function. In good working condition.
LCD Monitor Display & Belt-clip designed remote
100 levels of vibration
100 levels of static shock
With no jumps from 0 to 100 levels
300 meters remote controlling range
Rheostat dial allows for gradual adjustment in stimulation intensity
Four modes: static shock, vibration, beep and light
Clear LCD screen displaying level of stimulation collar
Over 3,000 different identity codes to prevent conflicts with other e-collars
The levels can be altered by use of up and down button.
A tone button activates a tone on the receiver.
The system can be used for 1 or 2 receivers. (This package had included 2 recievers)
The receiver will TURN OFF if it is unused for 4 minutes.
Any movement will activate the receiver into STANDBY MODE.
The transmitter will go into STANDBY MODE if there is no operation after 20 seconds and turn off after 2 minutes
About Transmitter
To install the batteries, open the battery cover.
the battery cover is at the back of the transmitter.
Open by sliding the over down.
Install 2 x 4LR4/6V batteries (Included) - ensure the the polarity is correct.
The transmitter will be TURN ON automatically.
Press the buttons one by one: the LCD images will be changed.
Press the up and down buttons on right hand side to set level
Choose channel 1 or 2 for 1 or 2 receivers
The LED light can be used for giving training signals.
The transmitter will go into STANDBY MODE if not operated for 20 seconds and will TURN OFF if not operated for 2 minutes.
In STANDBY MODE, press any button (except LED light button) to wake it up.
To TURN ON the transmitter, hold mode button at least 5 seconds
About Receiver and Matching with the Transmitter
Install the batteries
Remove the cover
Insert 2 x AAA/1.5V batteries (Not Included) ensure the polarity is correct.
The receiver will beep.
Go to the transmitter and choose Channel 1 or 2 to encode by pressing the channel button 1/2 in the transmitter.
Press the LAUNCH button on transmitter immediately.
The receiver will beep, by now, it has been encoded to the transmitter.
Replace cover and tighten metal probes.
How to Check the Static is Working
Use the test light LED - provided. Attach the light to the metal probes - select Static Mode - you can see static symbol on the screen - press the LAUNCH button - the LED will flash on.
Select a low number on the LCD display - put your fingers on the metal probes and press the launch button.
Package included:
1 x Transmitter
2 x Receiver
2 x Belt
Purchased about 6 months ago but used only a few times. Comes with 2 receivers and 1 remote to control 2 dogs at a time. I you do not wish to use the shock function (as this should be used together with training), you may adjust for vibration function only or the sound function. In good working condition.
LCD Monitor Display & Belt-clip designed remote
100 levels of vibration
100 levels of static shock
With no jumps from 0 to 100 levels
300 meters remote controlling range
Rheostat dial allows for gradual adjustment in stimulation intensity
Four modes: static shock, vibration, beep and light
Clear LCD screen displaying level of stimulation collar
Over 3,000 different identity codes to prevent conflicts with other e-collars
The levels can be altered by use of up and down button.
A tone button activates a tone on the receiver.
The system can be used for 1 or 2 receivers. (This package had included 2 recievers)
The receiver will TURN OFF if it is unused for 4 minutes.
Any movement will activate the receiver into STANDBY MODE.
The transmitter will go into STANDBY MODE if there is no operation after 20 seconds and turn off after 2 minutes
About Transmitter
To install the batteries, open the battery cover.
the battery cover is at the back of the transmitter.
Open by sliding the over down.
Install 2 x 4LR4/6V batteries (Included) - ensure the the polarity is correct.
The transmitter will be TURN ON automatically.
Press the buttons one by one: the LCD images will be changed.
Press the up and down buttons on right hand side to set level
Choose channel 1 or 2 for 1 or 2 receivers
The LED light can be used for giving training signals.
The transmitter will go into STANDBY MODE if not operated for 20 seconds and will TURN OFF if not operated for 2 minutes.
In STANDBY MODE, press any button (except LED light button) to wake it up.
To TURN ON the transmitter, hold mode button at least 5 seconds
About Receiver and Matching with the Transmitter
Install the batteries
Remove the cover
Insert 2 x AAA/1.5V batteries (Not Included) ensure the polarity is correct.
The receiver will beep.
Go to the transmitter and choose Channel 1 or 2 to encode by pressing the channel button 1/2 in the transmitter.
Press the LAUNCH button on transmitter immediately.
The receiver will beep, by now, it has been encoded to the transmitter.
Replace cover and tighten metal probes.
How to Check the Static is Working
Use the test light LED - provided. Attach the light to the metal probes - select Static Mode - you can see static symbol on the screen - press the LAUNCH button - the LED will flash on.
Select a low number on the LCD display - put your fingers on the metal probes and press the launch button.
Package included:
1 x Transmitter
2 x Receiver
2 x Belt
via Singapore Classified http://ift.tt/1d5fSE9
No comments:
Post a Comment